CASTLE EURO Especificaciones Pagina 82
- Pagina / 198
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Manual Euro-MERiDIAN
Chapter 11 Page 11 - 15
J: COMMUNICATIONS
OUTPUTS
(i) A Stand-Alone STU /
Dual-path signalling
device
Euro-22 and 28
A 10-pin connector is provided,
which can be used with a plug-
on loom (Cat. No. CT1105) to
connect to a STU or other
communicator.
This loom must be plugged on
with the BROWN wire towards
the TOP of the printed Circuit
Board (Pin 1 marking).
Euro- 10 and 12
An output module may be
wired to the unit to provide a
plug-on STU footprint.
Note: this module does NOT
currently monitor the inputs.
Alternatively, a slot-in adaptor
will be made available to fit
into the Digimodem slot and
provide a connector identical
to that on the Euro-22 and 28.
PLEASE CHECK FOR AVAILABILITY
The pin allocation for these
outputs is shown below.
Please ensure that the STU is
correctly programmed:
Pin Loom
colour
Program
o/p No.
Default
1BROWN
$
'Line Fault'
input
2RED
$
'RedCare Reset'
OR
'Fail to
Communicate'
input
3ORANGE
-
+12v supply
4 YELLOW 5 Mis
-
operation
(abort)
5 GREEN 1 Fire
6 BLUE 6 Confirmed
Any
7 MAUVE 3 Intruder Any
8 GREY 2 Zone PA Any
9 WHITE
-
0v supply
10 BLACK 4 Set All
NOTES:
$ - These inputs MUST be
enabled as shown on page 13-36.
Outputs provide +5v when
triggered. Software 3·1 has
“output invert” option is available
for use with ‘Positive Removed’
signalling (see page 13-35).
These outputs have insufficient
drive current available for any
other application.
Inputs are configured to accept
+ive triggers (5-12v).
- ENGINEERING 1
- Page (ii) September 2002 3
- Issue 3·1 Page (iii) 4
- Page (iv) September 2002 5
- Issue 3·1 Page (v) 6
- Page (vi) September 2002 7
- INTRODUCTION 8
- COMPLIANCE STATEMENT 9
- DD243:2002 9
- EXPANSION OF Euro-44+ 9
- WARRANTY 9
- Page 1 - 4 Chapter 1 11
- SYSTEM COMPONENTS 12
- SYSTEM ARCHITECTURE 14
- B: Euro-12 15
- C: Euro-22 16
- D: Euro-28 17
- E: Euro-44+ EoL Mode 18
- F: Euro-44+ iD Mode 19
- TMZ UNITS 21
- OUTPUT MODULES 21
- ACCESS CONTROL EQUIPMENT 21
- GUARD TOUR SYSTEMS 21
- INTELLIGENT POWER SUPPLIES 21
- SPECIFICATIONS 22
- C: OUTPUT CAPABILITIES 23
- D: HOUSING DIMENSIONS 23
- E: ELECTRICAL SPECIFICATIONS 24
- F: WIRING SPECIFICATIONS 25
- A: General Principles: 25
- C: End of Line Zone Wiring 25
- D: iD Wiring 25
- G: LOCATION OF ZONES 26
- Page 4 - 6 Chapter 4 27
- THE USER INTERFACE 28
- Page 5 - 2 Chapter 5 29
- (i) LEVEL SETTING 30
- (ii) AREA SETTING 30
- (iii) ALL SYSTEMS 30
- Page 5 - 4 Chapter 5 31
- E: SILENT SETTING 32
- F: EXIT MODES 32
- G: KEYSWITCH OPERATION 33
- H: UNSET ONLY INPUT 33
- I: FAIL TO SET 34
- J: SETTING WITH FAULTS 34
- K: SYSTEM CODES / TAGS 34
- L: VALID CODE SILENCES 35
- M: DEVICE FAILURE 35
- N: OTHER FAULT 35
- INDICATIONS 35
- INDICATIONS and TONES 36
- Page 6 - 2 Chapter 6 37
- (i) Customise Text Strings 38
- (ii) Display characteristics 38
- Page 6 - 4 Chapter 6 39
- PARTITIONING THE SYSTEM 40
- B: ZONES ‘ANY or ‘ALL’ 41
- C: Keyswitch Control 41
- D: Area Sounders 41
- EMERGENCY ALARMS 42
- B: FIRE ALARMS 43
- C: GAS ALARMS 43
- D: MIMIC DISPLAYS 43
- E: CALL SYSTEMS 43
- REMOTE SIGNALLING 44
- Page 9 - 2 Chapter 9 45
- Misoperation (Abort) 46
- Signalling 46
- Engineer Reset 46
- Digi Reply Signal 46
- E: SEQUENTIAL 47
- CONFIRMATION SIGNALLING 47
- OPERATION: 48
- COMPLIANCE WITH SPECIFIC 49
- REQUIREMENTS 49
- Chapter 9 Page 9 - 7 50
- Page 9 - 8 Chapter 9 51
- Chapter 9 Page 9 - 9 52
- Patent applied for 52
- Page 9 - 10 Chapter 9 53
- INSTALLATION 54
- B: MOUNTING THE 55
- EQUIPMENT 55
- C: TAMPER SWITCHES 55
- No. 6 round-head 55
- DANGEROUS 56
- AND enabled in the 57
- H: THE PRINTED CIRCUIT 58
- BOARD LAYOUTS 58
- (i) THE Euro-10 END STATION 58
- (ii) The Euro-12 END STATION 59
- Slotfor DigiModem 60
- Socket for 61
- (v) KEYPADS 62
- (vi) SET/UNSET TAG READERS 62
- (viii) OUTPUT MODULE 64
- (ix) INTELLIGENT POWER 65
- (x) PLUG-ON RELAY 66
- INTERFACE 66
- Page 10 - 14 Chapter 10 67
- WIRING THE SYSTEM 68
- C: WIRING SPECIFICATIONS 69
- D: RS.485 COMMUNICATIONS 70
- E. END of LINE DETECTION 70
- SINGLE RESISTOR WIRING 71
- DOUBLE RESISTOR WIRING 72
- F: iD Wiring 73
- System response cannot 73
- Chapter 11 Page 11 - 7 74
- Reminders for successful 75
- NOTE: When a Zone Expander 75
- G: iD COMMISSIONING 76
- READINGS 76
- Important Notes for 77
- H: OUTPUTS WIRING 78
- (i) SAB Connections 78
- (ii) End Station Outputs 79
- (iv) Output Module Outputs 79
- Chapter 11 Page 11 - 13 80
- (ix) Plug-on Relay Interface 81
- Output Identification 81
- J: COMMUNICATIONS 82
- (i) A Stand-Alone STU / 82
- Dual-path signalling 82
- (ii) A Plug-on STU / Dual 83
- POWERING UP and ADDRESSING 84
- COMPONENTS 84
- B: PRE-POWER UP 85
- C: POWERING UP 85
- ™ ™ ™ ™ ™ ™ ™[7] 86
- D: Keypad 87
- Indications Test 87
- PROGRAMMING THE BASICS 88
- EXIT ENGINEER MENU 89
- B: GENERAL 90
- PRINCIPLES 90
- C: NON VOLATILE 91
- D: PROGRAMMING 91
- OPTIONS: 91
- (iii) MODE SELECTION 92
- (iv) INSTALL ZEMs 93
- (v) ZONE PROGRAMMING 93
- Zone types: 95
- SECURITY PATTERNS 97
- ZONE ATTRIBUTES 98
- PROGRAMMING STEPS 99
- (vi) ASSIGNING KEYPADS 100
- (vii) CHANGING SYSTEM 102
- DISPLAYS 102
- Page 13 - 16 Chapter 13 103
- (viii) CHANGING TIMERS 104
- PROGRAMMING PROCEDURE: 105
- (ix) SET DATE and TIME 106
- (x) EXIT MODES 106
- (xi) PROGRAMMING CODES 108
- CODE TYPES and NUMBERS 108
- CODE CAPABILITIES 108
- PROGRAMMING 109
- PROCEDURE: 109
- Manual Euro-MERiDIAN 110
- Chapter 13 Page 13 - 23 110
- Page 13 - 24 Chapter 13 111
- (xiii) ALARM RESPONSES 112
- The following steps are 113
- SETTING systems: 113
- (xiv) PROGRAMMING 114
- Page 13 - 32 Chapter 13 119
- (xv) INTELLIGENT SETTING 120
- LEVEL SETTING SYSTEMS 120
- AREA SETTING SYSTEMS 120
- ALL SYSTEMS 120
- Programming Steps 121
- (xvi) SITE OPTIONS 121
- Repeat for other options to: 123
- (xvii) ENGINEER RESET 124
- (xviii) PROGRAMMING THE 124
- DIGI-MODEM 124
- Page 13 - 38 Chapter 13 125
- MANAGER TEST FACILITIES 126
- KEYPAD INDICATIONS TEST 126
- BATTERY TEST 126
- BATTERY LOAD TEST 126
- ENGINEER SYSTEM SET 127
- ENGINEER FORCE SET 127
- SOAK TESTING ZONES 128
- ENGINEER TEST FACILITIES 128
- Battery Test 129
- Outputs Tests 129
- SYSTEM DIAGNOSTIC 130
- FACILITIES 130
- Page 14 - 6 Chapter 14 131
- Calibrating ZEM iD output 132
- Page 14 - 8 Chapter 14 133
- SYSTEM LOGS 134
- Fault Codes 135
- VIEWING LOGS 135
- Chapter 15 Page 15 - 3 136
- Ward Control and Shunt Zones 138
- Operation of the Ward 139
- Programming a Ward: 140
- 2. SHUNTS 141
- Associated Outputs: 142
- Operation of the Shunt 142
- Programming the Shunt 143
- Zone and List 143
- Programming the 144
- Page 16 - 8 Chapter 16 145
- Use of Output Modules 146
- TERMINAL CONNECTIONS 147
- WIRING THE UNIT 148
- RS-485 Wiring: 148
- Outputs Wiring: 148
- PROGRAMMING THE 149
- A: FEATURES 150
- B: SYSTEM ARCHITECTURE 151
- C: INSTALLATION 151
- D: The Door Station 152
- E: WIRING 153
- Chapter 18 Page 18 - 5 154
- F: Addressing the 155
- G: Programming the 155
- Access Control 155
- (ii) Programming the 156
- H: SYSTEM LOGS 157
- J: PROGRAMMING 157
- K: Access Control 157
- Facility and DD243 157
- GUARD TOUR SYSTEMS WITH 158
- Euro-MERiDIAN 158
- C: Installing and Wiring 159
- D: Programming the units 159
- E: SYSTEM LOGS 159
- Installing the Euro-COM 9600 160
- DigiModem 160
- Page 20 – 2 Chapter 20 161
- 9600 to the End Station 162
- A: Features 162
- B: Safety and Installation 162
- C: The Euro-COM 9600 PCB 162
- D: Fitting the Euro-COM 162
- E: PSTN Wiring 163
- F: Programming the Unit 164
- G: Initialisation 164
- Page 20 – 6 Chapter 20 165
- ARC Signalling with the Digi 166
- Page 21 - 4 Chapter 21 169
- CONTENT TYPES AVAILABLE 171
- DOWNLOADING WITH 172
- Control from the PC 173
- Signalling modes 173
- Line Mode 173
- PC at Site 173
- PLANNING THE CALLS 173
- Priority: 174
- SMS Text Messages from Euro 176
- MERiDIAN 176
- Initialisation 177
- Page 23 - 4 Chapter 23 179
- _ _ _ _ _ 179
- _ _ _ _ _ _ _ _ _ _ _ 179
- [ ] 180
- Initialisation and Test 181
- Procedure 181
- Communication Failure: 181
- SYSTEM EXPANSION and 182
- ENHANCEMENT 182
- Cards Available: 183
- Page 24 - 4 Chapter 24 185
- CCTV or LIGHTING CONTROL WITH 186
- EURO-MERiDIAN 186
- Outputs: 187
- FAULTFINDING Euro-MERiDIAN 188
- Appendix A Page A - 3 190
- Page A - 4 Appendix A 191
- Appendix A Page A - 5 192
- Page A - 6 Appendix A 193
- Function Summary of change 196
- Issue 3·1 – September 2002 196
- Page B - 4 Appendix B 197
Comentarios a estos manuales
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad CASTLE EURO
(45 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Hello, im noob :)