CASTLE EURO Manual de instalación Pagina 15
- Pagina / 68
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Programming Manual EURO
RINS1291-3 Page: 15
Number & Type Operation
11 PTS
Active during exit time to complete Setting procedure
No audible or communicator response.
Note: May be used to act as ‘doorbell’ by use of ‘chime’ attribute.
12 Switcher
Active at all times. No audible or communicator response
Triggers associated output or switches other equipment
13 Day Alarm*
When set: Audible Response: Full.
Communicator: ‘Intruder’ and ‘Unconfirmed’ signals
When unset: Audible Response: Programmable.
Communicator: ‘Day Alarm’ signal
15
Ward
Control*
Input is allocated by system software and cannot be reprogrammed to
a different type, though relevant attributes may be adjusted.
16 Fault
Active when unset. Audible Response: Graduated internally
Triggers ‘Global Fault 1’ outputs if the system is set.
Triggers ‘Global Fault 2’ output if the system is set/unset.
17
Closure
Supervision
Active during Setting procedure. No audible or communicator
response. Prevents system being set whilst active
18
Shunt
Input*
Active at all times. No audible or communicator response
Accepts input from keyswitch (or equivalent) to shunt the inputs
assigned to it. Associated outputs are available. After 10 seconds the
detectors in the shunt list will be active. See page: 19
19
Unset
Input*
Active when set. Accepts input from keyswitch (or equivalent) to
Unset the Area/Level set assigned to it.
20
Keyswitch
Latched
Accepts input from keyswitch (or equivalent) to Set/Unset the Set
modes assigned to it. Setting includes normal exit time, etc. Requires
latching action switch
21
Entry Shock
Input
Active when system set. Works in conjunction with EE input type for
detection of forced entry. See page 16 for details.
22
Input Line
Fail
Active when fail. Will give a line fault alarm, and will signal telecom
line fault signal on expiry of line fault timer. Works in conjunction with
CCTV input.
23
Keyswitch
Pulsed
Accepts input from keyswitch (or equivalent) to Set/Unset the Set
modes assigned to it. Requires momentary action switch to toggle
set/unset state.
29 Interior
This will work the same as an Intruder type input, the only difference is
that when CID reporting is programmed then any inputs that are
programmed as Interior will report CID event 132.
32 Flood
This input type will work as a 24 hr input , any inputs that are
programmed for Flood will activate the external siren and will report
CID event 113.
39 CCTV
Active at all times. No audible or communicator response
If the input line fail is active, the system will signal CID/SIA events for
perimeter alarm and the CCTV input will open.
40 Perimeter
This will work the same as an Intruder type input, the only difference is
that when CID reporting is programmed then any inputs that are
programmed as Perimeter will report CID event 131.
41 Keybox
This input type will work similar to a switcher input, it does not trigger
an alarm but will report CID event 250 and is also a useful input type
when an output is required to to follow the Keybox type input.
42 Medical
This is a 24 Hr type input it will activate the external sounder and
report a CID event 100.
NOTES: ‘Part Set’ refers to any combination other than all available Areas
- Programming 1
- CONTENTS 3
- 3.3 Initial Power Up 8
- 3.5 Testing The Keypad 9
- 3.6 Text Programming 9
- 3.9 Set / Unset System 10
- 3.10 Forced Arm On Inputs 10
- 4.1 Clean Start 11
- 4.4.4 Input Response Time 13
- 4.4.5 Input XDF 13
- 4.5 Install ZEM 13
- 4.6 Change Inputs 14
- 4.6.1 Input Types 14
- 4.6.3 Creating a Common Area 16
- 4.6.4 Input Attributes 16
- 4.6.5 Masking Response 17
- 4.6.7 Shunt Inputs* 19
- 4.7 Assign Keypads/Readers 21
- 4.7.1 Reader Is: 21
- 4.7.2 **Set Point Sets 21
- 4.7.3 **Set Point Unsets 21
- 4.7.4 **Set Point In 21
- 4.7.6 Ward Control* 24
- 4.8 System Displays 26
- 4.8.1 Area Texts 26
- 4.8.2 Sign On Message 26
- 4.8.3 Site Name 26
- 4.9 Change Timers 27
- 4.12.2 Code Types 29
- 4.12.3 User Set Options 30
- 4.12.4 Flexi Set 30
- 4.13 Volume Control 32
- 4.13.1 Code Stops Sound 32
- 4.13.2 E / E Keypads Only 32
- 4.13.3 Alert Kps Only 32
- 4.14 Alarm Response 33
- 4.14.1 Silent 1st Alarm 33
- 4.15 Change Outputs 35
- 4.15.1 Output Types 35
- 4.16 Intelligent Set 41
- 4.17 Site Options 42
- 4.17.1 Site Option Types 42
- 4.18 Engineer Reset Options 44
- 4.19 Review Logs 45
- 4.19.1 Log Entries 45
- 4.19.2 Code Identification 45
- 4.19.3 Fault Codes 46
- 4.21 Diagnostics 50
- 4.22 Set Up Downloading 52
- 4.22.1 Download By 52
- 4.22.2 Security Mode 52
- 4.22.3 Telephone Line 52
- 4.23 Programme DIGI / SMS? 54
- 4.24 Dial Out Menu 61
- Device Fail 62
- Fault Indications 62
- One of the paths of the 64
- GSM/redcare has failed 64
- All paths on the 64
- GSM/redcare have failed 64
- QUICK FIND GUIDE 68
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad CASTLE EURO
(27 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales