CASTLE Meridian Especificaciones descargar pdf (Pagina 20)

Started Manual Castle Care-Tech Ltd

5·00 Page 39

VOLUME LEVELS

This applies to the system

‘

loudspeaker

’

output

–

levels

generated at Keypads are

programmed individually.

Each system tone may be

programmed to a pre

set volume

level, on a scale of 0 to 7.

The default levels are:

Intelligent set 2

Chime tone 3

Exit tones 3

Entry tones 4

Alert tone (tamper) 6

Alarm tones 7

NOTE: Level 1 is SILENT with an audible

chime (at volume level set for chime)

at the

end of settle time. Chime present at all

volume levels except 0. This may be used in

conjunction with Site Option “E/E Keypads

Only” when ‘Silent Set’ is required.

ALARM RESPONSES

Silent 1

Alarm

This prevents all system sounders from

becoming live until an alarm has been

'confirmed' - eg to prevent noise

interfering with audio confirmation

equipment. Only applies after panel

has been set for 3 minutes.

Disable Confirmation on entry

Used with a suitable FX, Unset or

Keyswitch input to disable all

sequential confirmation operation to

satisfy relevant options in DD243:2004.

Inputs to confirm after entry

Accepts 1 or 2 inputs to trigger after

expiration of entry time to qualify as

'sequentially confirmed' alarm.

NOTE: ONLY THE "2" SETTING

COMPLIES WITH DD243:2004.

Each area alarm response

may be

programmed with the option of

‘

graduated

’

functions, as can

‘

Day Alarm,

’

‘

Fire,

’

‘

Gas

’

and

‘

’

alarms. Graduation can

be between 'Keypads,' 'Internal Sounders,'

'Sirens only,' 'Digi' and 'Confirm.'

The following options are available for each:

Starts at _ _ _ _

Insert initial alarm level

Stops at _ _ _ _

Insert final alarm level

The response may thus be set to

graduate from keypad sounders to

internal sounders to sirens to digi

(remote signalling) to confirmed,

with 15 seconds at each level before

the next step.

NOTE: An additional upgrade level is

available if using Area setting.

To comply with EN50131, ‘Day

Alarm’ must be set to ‘Stop’ no

higher than Sirens Only.

PROGRAMMING STEPS:

With the display showing

ALARM RESPONSE?

Press YES

Area A Starts at

Keypads [1]

Use

to select from

‘

Keypads [0],

’

‘

Int Sounders [1],

’

‘

Siren only [2]

’

and

‘

Digi [3]

’

and press YES,

Area A stops at

Confirm [4]

Use

to select from

‘

Keypads

[0],

’

‘

Int Sounders [1],

’

‘

Siren only

[2]

’

‘

Digi [3]

’

or 'Confirm [4] and

press YES

Repeat for other areas, etc.

ALARM RESPONSE?

Press NO to move to next menu

item

Castle Care-Tech Ltd Euro-MERiDIAN Getting

Page 40 Software

PROGRAMMING OUTPUTS

Any output type may be

programmed to any of the

system outputs.

The most frequently used output

types are summarised below.

Additional output types are

available for advanced use – see

full Engineering Manual.

Outputs MUST be used within

their rated capacity.

Please note particularly the

differences between Hold Up, PA

and Duress. For general use the

default ‘HOLD UP’ should be used.

NOTE: To identify the STU output

numbers that correspond to the

communicator output pins/loom

colours, refer to table on pages 17,

18 & 19.

Type Default Active Restore

0000 Not Used Default setting except where shown

0001 Fire ATE 1 At Alarm When valid code entered

0002 Hold Up Any - At any HU/Duress alarm When valid code entered

0003 Intruder

ANY

- At alarm, while system

set

At first valid code entry

0004 Final Set ALL ATE 4 When system is FULLY

set

At code entry to unset

0005

Misoperation

ANY

(Abort)

When system silenced

after any

‘

intruder

’

output triggered

After 2 minutes

0006 Confirmed

ANY

ATE 6 When alarm is

sequentially confirmed

– see page 42

At next code entry

0007 Tamper Any ATE 5 Any tamper alarm At code entry to silence

0009 HU Device ANY ATE 2

At Alarm on a

HU device

(NOT Duress)

When valid code entered

NOTE: This output type responds ONLY to devices

wired into HU Inputs, NOT Duress Codes or 2-key PA

0010 Gas

At Alarm When valid code entered

0014 Siren

ANY

ES 1 When alarm live When alarm silenced, or when

Siren timer expires

0016 Strobe

ANY

ES 2 When alarm live When alarm silenced, or when

Strobe timer expires

0017 Omit Rearm

Any

ATE 7 At rearm at end of

confirm time, if zone in

fault isolated

When system unset

0018 Unconfirmed ATE3 Any tamper or intruder

alarm when system set.

At code entry to silence OR at

rearm (re-instatement) at end

of 'confirm' time.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 26 27

Comentarios a estos manuales

Sin comentarios

CASTLE Meridian Especificaciones Pagina 20

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad CASTLE Meridian