CASTLE Meridian Especificaciones Pagina 1

Castle Care-Tech Ltd Page 1 Euro MERiDIAN ‘G’ Range "GETTING STARTED

Started Manual Castle Care-Tech Ltd5·00 Page 19 Programming a STU (Excluding VERSUS GSM STU) STU Channel Default Output Type Panel

Started Manual Castle Care-Tech Ltd5·00 Page 21 9. POWERING UP and ADDRESSING the KEYPADS Pre Power-Up Checks Prior to powering up

Started Manual Castle Care-Tech Ltd5·00 Page 23 The system will check the current status of zones that would trigger an alarm if op

Started Manual Castle Care-Tech Ltd 4·00 Page 2511. PROGRAMMING THE SYSTEM CLEAN START It is essential that a ‘clean start’ be performed at initial

Castle Care-Tech Ltd Euro-MERiDIAN GettingPage 27

Started Manual Castle Care-Tech LtdPage 29

Started Manual Castle Care-Tech Ltd5·00 Page 31 ZONE ATTRIBUTES Attribute Response modification Chime System loudspeaker(s) will ‘

Started Manual Castle Care-Tech Ltd Page 33 Software ASSIGNING KEYPADS and TAG READERS Ensure that all Keypads and Tag Readers are correctly addres

Started Manual Castle Care-Tech Ltd5·00 Page 35 Timer Function Range Default AC signal Delay Time delay before Mains failure or Tec

Started Manual Castle Care-Tech Ltd5·00 Page 37 PROGRAMMING CODES and TAGS Codes may be 4-, 5- or 6-digit (It is preferable to avoi

Started Manual Castle Care-Tech Ltd 5·00 Page 3 2. SPECIFICATIONS A: ELECTR

Started Manual Castle Care-Tech Ltd5·00 Page 39 VOLUME LEVELS This applies to the system ‘loudspeaker’ output – levels generated at

Started Manual Castle Care-Tech Ltd5·00 Page 41 Type Default Active Restore 0022 Final Set ANY - When FIRST area is set At code

Started Manual Castle Care-Tech Ltd5·00 Page 43 INTELLIGENT SETTING LEVEL SETTING SYSTEMS Setting the system in pattern ‘A’ will c

Started Manual Castle Care-Tech Ltd5·00 Page 45 12. TEST AND DIAGNOSTIC FACILITIES AUTOMATIC TESTS BATTERY TEST The system performs

Started Manual Castle Care-Tech Ltd5·00 Page 47 SYSTEM DIAGNOSTIC FACILITIES The system diagnostics are available for all parts of

Started Manual Castle Care-Tech Ltd5·00 Page 49 13. SYSTEM LOGS Logs are fully date and time stamped, and are accessible from eithe

Castle Care-Tech Ltd Euro-MERiDIAN Getting Software Page 51APPENDIX: Summary of Principal Programming Options MENUS SUMMARY Menu UK Default Clean S

Started Manual Castle Care-Tech Ltd5·00 Page 53 Displays 34 Exit modes 36 Inputs 32 Intelligent Set 43 Keyp

Started Manual Castle Care-Tech Ltd 5·00 Page 5 3. END STATION TERMINAL LAYOUTEuro-G2 iD and EoL P20P1Slot for DigiModemSlot for MSX CardNVM2 NVM1F1

Started Manual Castle Care-Tech Ltd 5·00 Page 7 4. INSTALLATION GUIDANCE An intruder alarm system can be broken down into four major parts: 1. Cont

Started Manual Castle Care-Tech Ltd.3.00 Page 9 5. INSTALLING END STATION and KEYPADS THE END STATION Mount the End Station securel

Started Manual Castle Care-Tech Ltd5·00 Page 11 6. WIRING DETECTORS End of Line Wiring Grade 2 sytems Resistor colour code: 2K2 –

Started Manual Castle Care-Tech Ltd5·00 Page 13 Mount all detectors in the required locations, and wire them to the iD bus in any p

Started Manual Castle Care-Tech Ltd 5·00 Page 15Keypad Outputs Set/Unset Tag Reader Outputs TMZ Outputs 1 or 2 16ohm Speakersmay be wired in p

Started Manual Castle Care-Tech Ltd 5·00 Page 17COMMUNICATIONS OUTPUTS Remote communication is possible by: (i) The Snsp-In DigiModem This may be us